Book a WhatsApp demo
FREE TOOLS FOR GARMENT FACTORIES

Garment Sewing Defects List

Twelve common sewing defects with simple codes, causes, how to check and how buyers usually class them. Printable table and free CSV. No signup.

What are the most common sewing defects in garments?

Common sewing defects include open seams, skipped stitches, broken stitches, seam puckering, oil spots or stains, raw edges, untrimmed threads and garments not to size. Most come from machine settings such as thread tension, needle and feed, or from operator handling. The table below lists each one with causes and a check.

How are sewing defects classed as major or minor?

A major defect affects function, fit, durability or saleability, for example an open seam or wrong measurement. A minor defect is cosmetic, such as a loose thread or removable mark. The class is not fixed: buyers set their own list, and the same fault can be major on the collar but minor inside.

This page is a working summary for factory use, not a standard. The codes SD-01 to SD-12 are this page's own codes, not an industry code list. Where your buyer's quality manual or defect list says something different, the buyer's manual wins.

Sewing Defects Reference Table

Green rows (SD-01 to SD-08) are the eight one-tap defect tags on our own factory's QC device. Numbers in brackets point to the sources at the end of the page. Print prints only this table, on A4 landscape.

Garment sewing defects with code, description, causes, check and usual class
Code Defect What it is Typical causes How to check Usually classed
SD-01 Open seam The seam has come apart or was not closed, so the two plies separate along the seam line. Wrong or uneven seam inlay from operator handling, a wrongly set guide or folder; in extreme cases the seam bursts open [1]. Worker practice and machine set-up and maintenance [7]. Look along every seam inside and out; open the seam gently by hand at seam ends, joins and stress points. Major in the lists of SPS Commerce and V-Trust [6][4]. One company standard allows none except up to 5/8″ on hems [1].
SD-02 Skip stitch (skipped / jump stitch) The hook or looper fails to pick up the needle-thread loop, so a stitch is missed [1]; it shows as a sudden longer stitch [9]. Hook, looper or needle timing off; needle size or style wrong for the thread; fabric flagging from poor presser-foot control or a large throat-plate hole; bent needle; wrong tensions [2]. Needle blunt, bent or wrongly inserted [3]. Run a finger and eye along the stitch line looking for a longer stitch; check the first pieces after any needle change or machine repair. Depends on stitch type and buyer. One company standard allows no skips on chain or ravelling stitch, but two or fewer non-consecutive skips on lockstitch [1].
SD-03 Broken stitch One or more stitches are broken in the stitch line, at thread trimming or when the seam is stretched [9]. Wrong stitch type, too tight tensions, a second row of stitching running over the first and cracking it, sharp feeds, too much pressure [1]. Thread breakage from excessive tension, sharp edges on throat plate or hook, needle heat, poor thread [2]. Stretch the seam gently (especially on knits) and look for cracked or cut stitches; check where rows cross. Set by the buyer's list; V-Trust lists broken and skipped stitches among common sewing defects without a fixed class [5].
SD-04 Puckering A wrinkled, gathered effect along the seam line in otherwise smooth fabric [1]. It may only appear later, after the seam relaxes [9]. Variable differential feed, high thread tension, wrong thread balance, wrong thread type [2]. Operator handling, misaligned notches, thread shrinkage when wet; chain stitch puckers more than lockstitch [1]. Stitches too long for fine fabric [3]. Lay the seam flat and look along it under good light; on washed styles, check again after washing. Set by the buyer's list, by how bad it is and where it is [5].
SD-05 Oil stain Oil spots or stains on the garment, listed among sewing defects [1]. Oil from machinery and dirt from the factory floor [8]. Prevention: clean machines regularly and keep oil and grease away from the work [8]. Check both sides of the garment under good light, especially near seams sewn on that machine. Location decides. Spots and marks on less visible parts are minor examples [4]; the same fault in a highly visible zone can be classed higher [5]. Removable marks: minor [6].
SD-06 Raw edge A cut fabric edge left unfinished, not caught in the overlock or seam. Wrong or uneven inlay width from operator handling, wrongly set guide or folder; raw edges show in extreme cases [1]. Overlock stitch coming off the seam edge ("wrong overlock") [9]. Turn the garment inside out and check every overlocked and hemmed edge. Set by the buyer's list. One company standard: no raw edge on outside finished seams, none wider than 1/4″ inside [1].
SD-07 Uncut thread (untrimmed thread) Thread tails left on the garment after sewing. Among the most common apparel defects [7]. Dull knives and scissors; a factory layout that does not support trimming [7]. Check seam ends, bartacks and buttonholes inside and out. Usually minor (loose threads) [6]. But one company standard allows none on the outside if contrasting and visible [1], and V-Trust classes thread ends over 5 cm on infant garments as major [5].
SD-08 Measurement out of tolerance The finished garment is not to size [1]. Incorrect patterns, inaccurate marking or cutting, fabric shrinking or stretching, incorrect seam widths [1]. Measure the points on the buyer's spec sheet; measurements must not exceed the tolerance specified [1]. Major (incorrect measurements) [6].
SD-09 Uneven stitch density Stitch density is uneven along the stitch line [9]. Operator makes the machine snatch and does not let it control the fabric [1]. Stitch regulator wrongly set, feed dogs clogged with lint, wrong pressure or tension [3]. Count stitches over a set length at several places and compare with the spec. Often minor (small stitching inconsistencies) [6]; check the buyer's list.
SD-10 Seam grin The seam gapes and the stitches show when the seam is pulled across. Too loose a tension, too large a stitch, or the wrong stitch type [1]. Pull the seam gently across its width and look for a gap or visible thread. Set by the buyer's list.
SD-11 Needle damage / needle holes Holes, picked or ruptured threads along the stitch line [1]; on knits, cut marks on the stitching line [9]. Wrong needle size or type, blunt needle, needle heat, feeding difficulty [1]. Stretch the fabric next to the seam and look for holes or laddering. Set by the buyer's list. Separate from this: a broken needle found in a textile piece is a critical defect [4].
SD-12 Roping A twisted hem, found mostly at the bottom hem of the garment [9]. Uneven feeding of the top and bottom fabric layers while stitching [9]. Lay the hem flat and look for twisting. Set by the buyer's list.

Codes SD-01 to SD-12 are this page's own, not an industry standard. Classes vary by buyer, garment and defect location; the buyer's manual wins. Source: scanerp.pro/tools/sewing-defects-list.html (CC BY 4.0)

Why does the same defect get a different class?

Because major and minor are not fixed by the defect's name. The class depends on the buyer's own defect list, on where the fault sits on the garment, since a flaw on the collar counts for more than one inside, and on who will wear it, with stricter rules for infant wear. Check the buyer's manual.

Write the class your buyer uses next to each code on your own copy of this table, and use the same list for inline inspection, end-line checks and final AQL inspection.

What one knit factory actually logged

Source: Trishakti Apparel (Nepal, knit basics), station QC faults logged on the Scan ERP QC device, 5 Aug โ€“ 2 Nov 2026: 168 faults across 17 lots on 15 working days.

QC fault records by defect type, Trishakti Apparel, 5 Aug to 2 Nov 2026 (168 total)
DefectFaultsShareBar
Open seam5834.5%
Broken stitch4929.2%
Skip stitch3118.5%
Measurement out of tolerance2011.9%
Puckering84.8%
Uncut thread10.6%
Oil stain10.6%
Raw edge00.0%
Total168100%

Share = faults รท 168, rounded to one decimal, so the column adds to 100.1%. Bar length is relative to the largest count (open seam).

Three seam-integrity faults (open seam, broken stitch and skip stitch) make up 138 of the 168 records in this period.

Read this with care

Using the codes on the floor

About the CSV download

The download is a CSV file (UTF-8; opens in Excel, Google Sheets and LibreOffice). It has the same columns as the table above, plus a column of source numbers. Edit the "Usually classed" column to match your buyer before you use it.

How Scan ERP records these defects

In Scan ERP, the QC device has one-tap tags for the eight defects in the green rows. A fault is tied to the bundle and operation, the operator is told in Nepali by voice, and rework is assigned. You can see it in a demo.

Related guides and tools

Cite this page

You may copy, adapt and share this list under the CC BY 4.0 licence, with credit:

Scan ERP (2026). Garment Sewing Defects List: causes, checks and major vs minor. https://scanerp.pro/tools/sewing-defects-list.html. Licence: CC BY 4.0.

Sources

  1. "Apparel quality analysis: common defects in spreading, cutting, bundling, sewing, pressing and finishing, quality control in apparel production", Textile manufacturing and testing, INFLIBNET e-book. Includes a company workmanship standard reproduced as an example. ebooks.inflibnet.ac.in
  2. Coats, "Solving Your Sewing Problems", Technical Bulletin 06. coats.com
  3. W. Hamilton, "Checklist of Common Sewing Machine Problems", Guide C-202, New Mexico State University. pubs.nmsu.edu
  4. V-Trust, "Defect classification". v-trust.com
  5. V-Trust, "Workmanship Check in Garments". blog.v-trust.com
  6. SPS Commerce, "Quality Control and Inspection Standards in Apparel". spscommerce.com
  7. QIMA, "Your 6-Step Action Plan to Tackle Major Garment Defects". qima.com
  8. HQTS, "How to Prevent Garment Defects in Apparel and Textile Industry". hqts.com
  9. P. Sarkar, "Stitching Defects Found in Knits Garments", Online Clothing Study. onlineclothingstudy.com
  10. P. Sarkar, "Classify Garment Defects", Online Clothing Study. onlineclothingstudy.com

Factory counts: Trishakti Apparel QC device log, 5 Aug โ€“ 2 Nov 2026.

Defects Tagged at the Machine, Not on Paper

Scan ERP's QC device ties each fault to the bundle and operation and assigns the rework.

Book a Free Demo