Book a WhatsApp demo
FREE TOOLS FOR GARMENT FACTORIES

Shrinkage Test & Shade Check for Garments

A shrinkage % calculator for length and width, the ISO and AATCC methods behind the test, shade band and grey scale basics, and a printable test record with CSV. No signup.

How do you calculate fabric shrinkage percentage?

Mark a known distance on the fabric or garment, wash and dry it by the agreed method, and measure again. Shrinkage % = (after − before) ÷ before × 100, worked out separately for length and width. A minus result means the piece shrank; a plus result means it grew. Example: 50.0 cm becoming 48.4 cm is −3.2%.

Length change % = (Length after − Length before) ÷ Length before × 100
Width change %  = (Width after − Width before) ÷ Width before × 100
Minus (−) = shrinkage  ·  Plus (+) = growth (extension)

The formula and the minus-for-shrinkage, plus-for-extension convention are as printed in the free sample of ISO 5077:1984 (the withdrawn first edition). Always use the calculation and rounding in the current edition of the method your buyer names.

Shrinkage % Calculator

Enter the marked distances before and after washing, in the same unit (cm, mm or inches). Results update as you type. Pre-filled with the worked example below.

Length direction

Width direction

Buyer's limits (optional)

From the buyer's spec, e.g. 3 for −3% (−3 also works)
From the buyer's spec

−3.2%
Length: shrinkage
+1.2%
Width: growth

Enter the buyer's limits to compare.

No limits are built in, on purpose. The public ISO and AATCC pages quoted below give no pass/fail figure; your buyer sets the allowed shrinkage and growth. The buyer's manual always wins over this page.

Worked example

Illustrative numbers, not data from a real test, and 50 cm is not quoted from any standard: the marking distances are set in ISO 3759 or the AATCC method you use.

These are the numbers pre-filled in the calculator above, and the same figures appear in the example row of the record below and in the CSV.

Which standards cover shrinkage testing of fabrics and garments?

The main ISO set is ISO 5077 for dimensional change in washing and drying, ISO 6330 for the domestic washing and drying procedures, and ISO 3759 for preparing, marking and measuring specimens. AATCC TM135 covers fabrics and AATCC TM150 covers garments after home laundering. The buyer's test request says which method applies.

Standards for shrinkage and colour assessment
StandardTitleScope, as the official page describes it
ISO 5077:2007Textiles — Determination of dimensional change in washing and dryingA method for the dimensional change of fabrics, garments or other textile articles after a specified combination of washing and drying procedures.
ISO 6330:2021Textiles — Domestic washing and drying procedures for textile testingDomestic washing and drying procedures for textile testing, plus reference detergents and ballasts. A complete test is one washing and one drying procedure.
ISO 3759:2011Textiles — Preparation, marking and measuring of fabric specimens and garments in tests for determination of dimensional changeHow to prepare, mark and measure fabrics, garments and fabric assemblies for dimensional change tests, for woven and knitted fabrics and made-up articles.
AATCC TM135Dimensional Changes of Fabrics after Home LaunderingLength and width changes of fabrics under home laundering; applies to all fabrics suitable for home laundering. AATCC lists it as related to ISO 3759.
AATCC TM150Dimensional Changes of Garments after Home LaunderingLength and width changes of garments under home laundering; may not apply to garments made of certain stretch fabrics.

Useful details from the official pages

Titles and scopes are summarised from the public catalogue pages at iso.org and aatcc.org. The full standards are paid documents; buy the current edition before you run a test for a buyer. This page is a working summary, not a substitute for the standard or the buyer's own policy.

How is shade checked in the garment industry?

Fabric rolls are inspected and sorted by shade, a shade band is made and approved, and each roll is marked with its shade band number. Rolls of the same shade are spread together in a lay, so all parts of one garment come from one shade. Colour is judged under a defined light source the buyer names.

Where shade variation comes from

Fabric is dyed in batches, so when an order is dyed in several lots there can be shade differences between lots. Inside one roll, shade can also vary from centre to selvedge and along the length, and it can vary from roll to roll.

Shade band and shade continuity card

One published fabric-warehouse procedure for garment factories runs the steps in this order before cutting:

  1. Shade blanket washed as per the bulk recipe
  2. 100% shade segregation of rolls
  3. Shade-wise colour continuity card
  4. Shrinkage measurement
  5. Master roll selection
  6. Shade band making, shade band washing and shade band approval
  7. Fabric issued to cutting shade-wise, with a shade note

The same procedure lists running shade and centre/selvedge shade as checks during fabric inspection, and shrinkage among the in-house lab tests. Your buyer may require a different sequence; follow theirs.

Cutting and sewing by shade

Standard light source

Colour should be judged under defined and repeatable lighting, because two samples can match under one light source and not under another (metamerism). A light booth gives controlled, repeatable viewing conditions. If the buyer requires a specific source such as TL84, CWF or D65, use that source in a calibrated, maintained booth, and use matching sources at every supplier location.

Grey scale and visual assessment

Note the difference: the grey scale standards above are written for colour fastness tests (colour change after a test such as washing). Comparing bulk fabric with an approved shade standard is the visual colour-difference assessment that AATCC EP9 covers. How much difference is acceptable between rolls or panels is set by the buyer, not by these pages.

Shrinkage Test Record (printable)

The first row is the worked example (green), calculated by this page. Print prints only this sheet, on A4 landscape. Or download the same columns as a CSV.

Buyer / style / PO:
Buyer's limits (length / width):
Checked by:
Shrinkage test record

Change % = (After − Before) ÷ Before × 100  ·  − = shrinkage, + = growth  ·  Limits are the buyer's  ·  Format: scanerp.pro/tools/shrinkage-shade-check.html

About the CSV download

The download is a CSV file, not an .xlsx workbook. It opens in Excel, Google Sheets and LibreOffice, but it holds no formulas: the shrinkage formula is written as a note at the top. It has the same columns as the printable record, one illustrative example row to delete before use, and blank rows.

How Scan ERP helps

Scan ERP tracks every cutting lot and bundle by colour and size, so you can see which lot and colour each bundle came from. Its QC device has a "Measurement" defect tag for out-of-tolerance pieces. It does not replace your lab's shrinkage or shade tests. See a demo.

Related guides and tools

Cite this page

You may copy, adapt and share this page, including commercially, under the CC BY 4.0 licence, if you credit it:

Scan ERP (2026). Shrinkage Test & Shade Check for Garments. https://scanerp.pro/tools/shrinkage-shade-check.html. Licensed under CC BY 4.0.

Know Which Lot and Colour Every Bundle Came From

Scan ERP tracks every cutting lot and bundle by colour and size.

Book a Free Demo